The Seiko S is a professional class watch case opener for watch with snap on case backs. This tool lets you easily open snap on watch backs easily and safely, without the risk of scratching. The main feature, and advantage, of this opener is that it holds the watch in a vise and opens with the blade in an all-in-one unit. Insert the four posts into the appropriate post holes according the size of you watch case. There are four posts with nylon tips to help hold the watch without scratching or marring the case.
Two additional posts are supplied with the tool and stored in the back of the unit. Place the watch on the case vise with the face down and the case back notch if there is one facing the blade.
You can rotate the base to help line up the case back notch with the opening blade. Tighten the case vise to secure with watch with the knob A on the front of the tool. On the back of the tool is storage for a pair of additional case holding pins that can be placed in the central platform. There is also a spare blade holding slot located in the central platform. A US patent 5,, was awarded for this tool in February This is a simple case holder that allows the removal of snap case backs when secured against a work table edge.
It has synthetic rubber on the top and bottom surfaces to prevent scratches and slipage. This is a basic case opening tool that is designed to open snap back cases.
This is a case opening tool with an extra narrow blade surface. This tool is designed to open two piece cases that are held together in a spring loaded configuration. In between the lugs there are a pair of holes that house a spring that must be simultaneously depressed to allow the two parts of the case to be separated.
Grease for mainsprings. After removing the old grease and cleaning a mainspring this is the grease used. This is a two part epoxy adhesive used to glue a crystal into some "non-waterproof" cases.
To use mix equal parts from tube A and tube B for approximately 1 minute. When applied it should be left for 12 hours at room temperature to cure and it will fully cure after 24 hours. This is a 5 gram tube of silicon based adhesive designed for use on bracelet screws. As it is silicon based it remains flexible even after curing. This is a 10 gram adhesive used to secure watch crystals on some case designs.
This is a general grease used in watch service. Check the movement service guides for indication where this should be applied. This is a tool to test the waterproofing of a watch after it has been serviced and gaskets replaced. The unit has a carbon dioxide canister that pressurises the chamber. A watch is then submerged into water and you can observe if there are any bubbles emanating from the watch case indicating a leak.
This is a movement holder for chronograph calibres. This allows the movement to be securely held during service and also allows the hand positions to be set. This is a movement holder for chronograph calibre. This tool was distributed in both a blue and white packaging.
The S is an updated version of the S that supports both the and chronograph calibres. This is a movement holder set for working on the perpetual calendar 4F and 8F caliber movements. This Universal Movement Holder is made of plastic ensuring it will not to damage a movement, and can be used for repairing any type of movement.
This is a jig used with assembly and disassembly of movements. The conductive rubber surface protects movements from static electricity. The square shape makes it easier to turn in any direction. This is a tool that is used for measuring the output torque of the centre wheel and pinion on various early quartz movements.
To operate this tool the watch being tested is placed in a movement holder and then located in the notch in front of the measuring arm. The watch is put int the time setting position and the minute hand adjusted to rest against the gauge. The watch is then operated and the gauge read once the second hand has stopped moving. This is a battery hatch removal tool.
The different sized ends are used to open different shaped battery hatches. The S is a desk mat that is grounded along with the user. This is designed for the servicing of digital watches to prevent static discharge from damaging electronic components. This type of mat is commonly used in the electronics industry and is a simple way of minimizing any potential damage from static on the items being serviced.
The operator wears a strap that is connected to the mat, the mat is also connected to ground via a detachable lead, ensuring that the user and work surface are commonly grounded. This is an analog multi-meter designed to check the voltages, current consumption and connectivity of electronic watches and clocks.
This is an adjustable two prong case opener for screw case back opening. This has a maximum opening distance of 20mm so is suitable for ladies watch cases.
This jig allows a battery to be externally mounted and then power applied to a movement through a pair of probes. This is useful for working on a quartz watch when the battery can not be held in place via the usual method.
The S is a digital multi-meter designed to work on quartz movements. You are able to measure current consumption, connectivity and voltages. This is an accessory for the S multi tester. It allows the testing of button batteries by placing them in a spring loaded slot section. It is also possible to use this as a current supplier when testing the power consumption of a watch circuit. There is a switch to the side that changes between battery test and power supply modes.
These are a pair of probe cables that can be attached to the S digital multi-meter to allow connection and measurement of different movements.
This is a simple battery tester that shows the voltage of a battery. The battery to be tested is placed on the metal disc and the probe touched to the negative side of the battery. The digital display shows the voltage the battery produces. This is an updated version of the S digital battery tester. The operation and functionality is the same but this is a newer variant. This is a multi tester developed specifically for watch repair. It allows measuring of the current consumption according to hand movement of the watch and by setting the gate time, it is possible to measure more accurately.
There is a built-in power supply can can provide voltage from 1. It has an auto range function that automatically switches the measurement range. An auto off function prevents battery exhaustion if not used it in about 20 minutes. It is a multi-tester dedicated to watches that can measure the battery voltage of watches.
It is also possible to measure the current consumption of the movement and the coil resistance value. Power: 2 AA alkaline batteries, battery life hours alkaline batteries, when the backlight is off , auto off 20 minutes after final operation. These are generic finger cots used to protect movements and parts when working on watches. They are relatively thick and are reusable. This is a dedicated battery removal tool designed for the 4F and 8F perpetual calendar calibers. This is a screwdriver for band adjustment used to loosen and tighten the bracelet adjustment screws.
It has a thick handle so that it can be easily turned even with a difficult screw. The screwdriver blades are replaceable and a set of five replacement blades is provided with part S This is a dedicated tool piece that is designed to remove the central screw of the automatic rotor on 4S caliber movements.
This unit fits into the S screwdriver. The S is designed to allow easy adjustment of a wide range of watch bracelets. The set comes with a couple of screwdrivers with interchangeable bits both flat blades and rounded probes. There is also a large weighted base that has a special bit that is placed in it. This base holds the bit upright to make it easier to insert into the bracelet being adjusted.
Used to apply silicon grease onto gaskets. The case opens and there is an applicator that allows the even coating of silicon grease to be applied. The S Bracelet Cutter is a power tool used to size a number of bracelet styles like mesh that do not have individually sized links. The watch owners wrist is measured and then the bracelet is cut to size. This is a similar to the mechanical guillotine style cutters but instead employs a motor driven cutting wheel. This is a tool designed for the removal and fitting of band securing pins that are held in place with the C ring type, pipe type and pin types.
A set of replacement tool tips is available in set S The case opener blade is made of hardened steel and measures 2. After the watch is secured into the case vise, the vise is rotated to position the blade in alignment to the opening notch position of the watch case back. The blade is then tightened against the watch back until it opens, the blade can be gently twisted to add a little more opening force as needed. Includes an extra opening blade and two plain posts or pins which fit conveniently into the unit for storage.
Instruction sheet with diagram and component i. Made in Japan.
0コメント